Skip to main content

Apache Status Codes

Often when debugging a problem or looking through your logs you will see the apache status codes

For Example
xxx.xxx.xxx.xxx - - [28/Jul/2006:13:49:28 +0200] "GET /news.php HTTP/1.1" 200 807 "http://www.joe-ma.co.za/news.php" "Mozilla/5.0 (X11; U; Linux i686; en-US; rv:1.9a1) Gecko/20060703 FreeBSD/amd64 Minefield/3.0a1"





Successful Client Requests
200 OK
201 Created
202 Accepted
203 Non-Authorative Information
204 No Content
205 Reset Content
206 Partial Content

Client Request Redirected
300 Multiple Choices
301 Moved Permanently
302 Moved Temporarily
303 See Other
304 Not Modified
305 Use Proxy

Client Request Errors
400 Bad Request
401 Authorization Required
402 Payment Required (not used yet)
403 Forbidden
404 Not Found
405 Method Not Allowed
406 Not Acceptable (encoding)
407 Proxy Authentication Required
408 Request Timed Out
409 Conflicting Request
410 Gone
411 Content Length Required
412 Precondition Failed
413 Request Entity Too Long
414 Request URI Too Long
415 Unsupported Media Type

Server Errors
500 Internal Server Error
501 Not Implemented
502 Bad Gateway
503 Service Unavailable
504 Gateway Timeout
505 HTTP Version Not Supported
Labels:

Comments

Post a Comment

Popular posts from this blog

Setting up and Installing Rancid on FreeBSD for Cisco Products

Setting up and Installing Rancid on FreeBSD for Cisco Products What is Rancid? Rancid is an application that monitors a devices configuration including software and hardware. The configuration is then stored in a Concurrent Version System or CVS. Most of the time it is used to back up router, switch and firewall configurations, as well as notify you when a configuration has changed, i.e a firewall rule or a routers IP address or access list change. here is an example of the output =================================================================== retrieving revision 1.29 diff -u -4 -r1.29 mpls-jhb-pe1 @@ -288,9 +288,9 @@ ! interface Serial0/0 description Link to Client X bandwidth 2048 - ip address 192.168.1.244 255.255.255.254 + ip address 192.168.1.234 255.255.255.254 ip route-cache flow ip tcp header-compression iphc-format ip tcp compression-connections 256 ! ip ospf message-digest-key 1 md5 the - symbol represents what was removed the + symbol represents what was added The abo
2 comments
Read more

Tacacs+ Install and Config Guide

Tacacs+ Install and Config Guide What is TACACS As per wikipedia Terminal access controller access control system (TACACS) is a remote authentication protocol that is used to communicate with an authentication server commonly used in UNIX networks. TACACS allows a remote access server to communicate with an authentication server in order to determine if the user has access to the network. Installing Tacacs on FreeBSD This guide is intended to be a basic implementation of TACACS+, so although there are may features I am just going to document what I generally use. Please note that tac_plus is also available from Shrubbery Networks if you would like to install and configure on another platform. You may also want to check out my Rancid How-To Once again its in your ports directory. cd to /usr/ports/net/tac_plus4/ run a "make install clean" Once installed vi /usr/local/etc/rc.d/tac_plus.sh Then Change the following line from NO to YES tac_plus_enable=$ Save the file, then vi /e
Post a Comment
Read more

Setting up a Cisco 800 series Router for ADSL

Setting up a Cisco 800 series Router for ADSL Not that the Average user would use a Cisco ADSL router, or if they do use a Cisco product it would probably be a Linksys router. Anyway here is the config with comments in between. all comments are in italics You might want to check out the Cisco DYNDNS configuration guide too NOTE: This particular config was done on a Cisco 877 ADSL / DSL router however its known to work on the Cisco 800 series DSL routers in general including the Cisco 827 Cisco 837 Cisco 877W This example is a basic setup for just access to the web you can enable PAT or Port Address Translation on the router to allow access from the outside to a server or something like that. Also this setup is for a Dynamic IP from the ISP you might also want to checko out the how to on setting up SSH login on the router no service pad service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname # your router name i.e. Bobs Router ! boot-st
Post a Comment
Read more